TROY-BILT LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019Printed In USAOp e r a t O r ’s Ma n u a lSafe Operation Practices • Set-Up • Operation • Ma
Connecting the Battery CablesCALIFORNIA PROPOSITION 65 WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds, che
Adjusting the Seat To adjust the position of the seat, pull up and hold the seat adjustment lever. Slide the seat forward or rearward to the desired p
Deck Lift LeverPTO (Blade Engage) HandleSystems Indicator MonitorBrake PedalThrottle/Choke ControlIgnition Switch ModuleDrive/Reverse PedalCup HolderP
Deck Lift LeverDECKHEIGHTLOHIchange the height of the cutting deck. To use, move
Fuel Level IndicatorThe Fuel Level Indicator is located on the left side of the tank.PTO/Bl
TO AVOID SERIOUS INJURY OR DEATH• GO UP AND DOWN SLOPES, NOT ACROSS. • AVOID SUDDEN TURNS.• DO NOT OPERATE THE UNIT WHERE IT COULD SLIP OR TIP.• I
Driving The TractorWARNING! Avoid sudden starts, excessive speed and sudden stops. Lightly press the brake pedal to release the parking brake. Mov
Driving On Slopeswhere you may operate the tractor safely.WARNING! Do not mow on inclines
Engaging the PTOMove the Throttle/
Maintenance ScheduleBefore Each useEvery 10 HoursEvery 25 HoursEvery 50 HoursEvery 100 HoursPrior to StoringClean Hood/Dash LouversP PCheck Engine Oi
Customer SupportPlease do NOT return the machine to the retailer or dealer without first contacting the Customer Support Department.If you have diffic
3. Remove the oil fill cap/dipstick from the oil f
Attach the hose coupler to the water port on your decks 3. Turn the water on.
AdjustmentsWARNING! Shut the engine off, remove the ignition key and engage the parking brake before h
Leveling the Deck (Side to Side)If the cutting deck appears to be mowing unevenly, a side to side adjustment can be performed. Adjust if necessary as
Cutting Deck Removalposition and engage the parking brake.Lower the deck by moving the deck
Remove the cotter pin from the end of the stabilizer rod and slide the stabilizer out of the hanger bracket on the deck. See Fig. 7-5.Gently slide
It may also be necessary to loosen the hex nut on the left 3. idler pulley to get the belt off the pulley and around the belt guard.Carefully remove t
2. baffle and the cutting blade to act as a stabilizer. Remove the hex flange nut t
ChargingWARNING! Batteries give off an explosive gas while charging. Charge the battery in a well ventilated area and keep away from an open flame or
Problem Cause RemedyEngine fails to start 2. Spark plug wire disconnected. 3. Throttle/C
Important Safe Operation Practices23General OperationRead, understand, and follow all instructions on the machine and in the manual(s) before attem
Component Part Number and Description
you purchased yo
Notes1133
FEDERAL and/or CALIFORNIA EMISSION CONTROL WARRANTY STATEMENTYOUR WARRANTY RIGHTS AND OBLIGATIONSMTD Consumer Group Inc, the United States Environment
GDOC-100223 Rev. AWARRANTED PARTS:The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such w
MANUFACTURER’S LIMITED WARRANTY FORGDOC-100020 REV. AThe limited warranty set forth below is given by Troy-Bilt LLC with respect to new merchandise pu
4 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sA missing or damaged discharge cover can cause blade contact or th
5se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sChildrenTragic accidents can occur if the operator is not alert to the
6 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e s3. complete stop wi
7se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSafety SymbolsThis page depicts and describes safety symbols that may a
8 se c t i O n 2 — iM p O r t a n t sa f e Op e r a t i O n pr a c t i c e sSight and hold this level with a vertical tree...or a corner of a buil
Tractor Set-UpMoving The Tractor Manuallyrelief valve for occasions when it is necessary to
Commentaires sur ces manuels