Troy-bilt 634B-Super Bronco Manuel d'utilisateur

Operator’s ManualRear-tine Tiller Models 630B—Tuffy®634F—BroncoTM634B—Super BroncoTMWarning: This unit is equipped with an internal combustion engine

Features and Controls3Section10INTRODUCTIONThis Section describes the location andfunction of the controls on your tiller.Refer to the following Secti

Section 3: Features and Controls 11FORWARD CLUTCH BAILThe Forward Clutch Bail (E, Figure 3-4)controls the engagement of forward driveto the wheels

Operation4Section12INTRODUCTIONRead this Operation Section and the sepa-rate Engine Owner’s Manual before youstart the engine. Then, take the time to

Section 4: Operation 13Stopping the Engine and Tiller1. To stop the wheels and tines, releasethe Forward Clutch Bail (all models) or theReverse Clu

14 Section 4: OperationPreparing SeedbedsFig. 4-6Fig. 4-7• If the garden size will not permitlengthwise and then crosswisetilling, then overlap the fi

Section 4: Operation 15TILLING TIPS & TECHNIQUES (cont.)Power composting simply means tilling under and burying in the soil all manner oforgani

16 Section 4: OperationThe tines have a self-clearing action which eliminates most tangling of debris inthe tines. However, occasionally dry grass, s

Maintenance5Section17Before inspecting, cleaning or servicing the machine, shut off engine,wait for all moving parts to come to acomplete stop, discon

18 Section 5: MaintenanceBefore inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts tocome to a complete stop, d

Section 5: Maintenance 19Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts tocome to a complete stop,

For more details about your unit, visit our website at www.troybilt.comTABLE OF CONTENTSContent PageCalling Customer Support . . . . . . . . . . . . .

20 Section 5: MaintenanceBefore inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts tocome to a complete stop, d

Section 5: Maintenance 21Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts tocome to a complete stop,

22 Section 5: MaintenanceBefore inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts tocome to a complete stop, d

Parts List 23Models 634F, 634B and 630BDRAWING NO. 11 710-0599 Hex Hd. Flange Screw, Self-Tapping,1/4-20 x 1/2 ... 23

24 Parts ListModels 634F, 634B and 630BDRAWING NO. 2

Parts List 25Models 634F, 634B and 630BPARTS LIST - DRAWING NO. 2REF. PARTNo. No. DESCRIPTION QTY.REF. PARTNo. No. DESCRIPTION QTY.1 GW-55104 Upper Ha

26 Parts ListModels 634F, 634B and 630BDRAWING NO. 4REF. PARTNo. No. DESCRIPTION QTY.REF. PARTNo. No. DESCRIPTION QTY.1 GW-9512 Retainer, Snap Ring, “

Parts List 27Models 634F, 634B and 630BDRAWING NO. 51 GW-9727 Plug, Transmission Oil Fill ... 12 1186328 Hex Hd. Flange Screw, 5/16-18

28 Parts ListModels 634F, 634B and 630B334411451330254647152540383924244310262912213615, 4730142225482732343416183877233192031524414225673332419144171

Parts List 29Models 634F, 634B and 630B1 * Engine, Recoil Start... 12 1917326 Bracket, Belt Cover...

Safety1Section3Training1. Carefully read this Owner’sManual, the separate EngineOwner’s Manual, and anyother literature you may receive. Be thor-oughl

30 Parts ListModels 634F, 634B and 630BDRAWING NO. 7RIGHT SIDELEFT SIDELeft Hand TineRight Hand TineHold Tine With Blunt End Toward YouNOTE: Identify

Parts List 31Models 634F, 634B and 630B1 710-3005 Hex Hd. Screw, 3/8-16 x 1-1/4, Grade 5 162 50049-01 Bolo Tine - Right Hand. Single tine used on lef

TROY-BILT TILLER LIFETIME LIMITED WARRANTYWHAT PRODUCT All Troy-Bilt branded rear tine walk-behind tillers with gear drive transmissions.IS COVERED T

4 Section 1: Safety4. Exercise caution to avoid slipping orfalling.5. If the unit should start to vibrate abnor-mally, stop the engine, disconnect the

Section 1: Safety 5DecalsFor your safety and the safety ofothers, various safety and opera-tional decals are located on yourunit (see Figure 1-2). Ke

Assembly2Section6INTRODUCTIONCarefully follow these assembly steps tocorrectly prepare your tiller for use. It isrecommended that you read this Secti

Section 2: Assembly 72. Remove the hairpin cotter (L, Fig. 2-3)and wheel drive pin (M) from the wheelhub (O) and wheel shaft (N). 3. Slide the wheel

8 Section 2: Assembly4. Thread the #10-24 hex nut (Z, Fig. 2-5)halfway onto the screw (V). 5. Thread the screw (V) into the cableadjuster (X).6. Hook

Section 2: Assembly 9STEP 6: CHECK LEVEL OF TRANSMISSION GEAR OILThe transmission was filled with gear oil atthe factory. However, you should checkthe