Troy-bilt 47330 Manuel d'utilisateur

SAFI^ FIRST!Before operating t№ egnlitoient, read this Owner’s Manntlwt^M№a!e manual supplied Iqr tin tngli^iwMfacturer.Models4732947330$4.50OWNER’S M

10 Section 3: Features and ControlsFigure 3-S: Squeeze clutch lever against handlebar when starting engine. Release clutch lever slowly after engine s

Section4I OperationA WARNINGBefore operating the unit, carefuiiy read and understand all safety, controls and operating instructions in this Manual, i

Section 4: Operation4. Push the rocker ON/OFF switch (Figure 3-8) to the ON position.5. Squeeze the clutch lever (Figure 3-5) up against the handle.

Section 4: OperationListed below are materials suitable for shredding, along with any special processing conditions. NOTE: If the material is wet or

14 Section 4: OperationUSING THE SHREDDERIMPORTANT: Always wear safety goggles (with side shields), appropriate gloves, and hearing protection. Read a

Section 4: Operation 15JWet, soggy, or “green” materials will be shredded to a medium consistency when using the Bar Grate. However, to shred these ma

Section 4: OperationFigure 4-7: The illseharge screen must be positioned as shown above. The holes In the tubes at tbe screen ends

Section51 MaintenanceA WARNINGMoving parts on the unit can cause serious personai injury.Shut off the engine, iet aii moving parts stop completeiy, d

18 Section 5: MaintenanceA WARNINGFaiture to foitow these instructions can resutt in serious personat injury or property damage.Before inspecting, cie

Section 5: Maintenance 19Before Inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a

Dear Owner;Thank you for purchasing this Chipper/Shredder. This unit has been designed, engineered and manufactured to give you the best possible depe

20 Section 5: Maintenance'AA WARNINGFaiiure to foiiow these instructions can result in serious personal injury or property damage.Before inspecti

Section 5: Maintenance 21JBefore inspecting, cieaning or servicing the machine, shut off engine, wait for aii moving parts to come to a

22 Section 5: MaintenanceA WARNINGWFailure to follow these instructions can result in serious personal injury or property damage.Before inspecting, ci

Section 5: MaintenanceBefore inspecting, cieaning or servicing the machine, shut off engine, wait for aii moving parts to come to a com

24 Parts ListDrawing No. 1Models 47329 and 4733040,V./"iSjf /30id"\N 1s. \_____________________LI \28*-iT'.-.^8230120071>* N7024.23

ifiartslistJHodels 47329 and 47330Ref.Part No.DescriptionQty.Ref.Part Ne.DescriptienQty.2 1773249010Closure Assembly, Left Hand... 1541766972E

2S Parts ListModels 47329 and 47330Drawing No. 2 15Ref.Part No. Description Qty.Ref. Part No. DescriptionQty.1 1762607 Cylinder Weldment...

CUSTOMER SERVICE INFORMATIONOwner Registration CardPlease fill out and mail the enclosed owner registration card. The purpose of this card is to regis

Sectionn SafetySPARK ARRESTER WARNING TO RESIDENTS OF CALIFORNIA AND SEVERAL OTHER STATESUnder California law, and under the laws of several other sta

4 Section 1: Safety6. Handle fuel with саге. It is highly flammable and has explosive vapors. Take these precautions;a. Use an approved fuel containe

Section 1: SafetyMaintenance and Storage1. Before performing any maintenance or adjustments, shut the engine off, wait for all moving parts to come t

Section21 AssemblyA WARNINGTo prevent personal injury or property damage, do not start the engine until all assembly steps are complete and you have r

Section 2: AssemblyJSTEP 4: AHACH HANDLE1. Using two 7/16" wrenches, remove the handle (F, Figure 2-3) and discard the screv№ and nuts. Turn the

Section3I Features and ControlsA WARNINGBefore operating your machine, carefully read and under- sfand all safety, controls, and operating Instruction

Section 3: Features and Controls 9A DANGERContact with rotating cutting blados will cause serious personal injury. Do not put hands, face, feet or clo