Operator’s ManualRear-tine Tiller Models630C— ,634F— Bronco™...634B — Super BroncoModel 634B ShownIMPORTANT: READ SAFETY RULES AND INSTRUCTIONS
SECTION 3: FEATURES AND CONTROLSA.WARNING: Before operating your machine, carefully read and understand all safety, controls and operating instruction
AA,WARNING: Before starting engine, be sure that both wheels are in WHEEL DRIVE position. See WhesI Drive Pins for instructions.Engaging the Forward C
SECTION 4: OPERATIONA.WARNING: Before operating your machine, carefully read and understand all safety (Section 1), controls (Section 3) and operating
A WARNINGKEEP AWAY FROM ROTATING TINEG. ROTATING TINES WILL CAUSE INJURY.Stopping the Engine and Tiiler1. To stop the wheels and tines, release the Fo
TILLING TIPS & TECHNIQUESTilling DepthsAWARNING: Before tilling, contact your telephone or utilities company and inquire if underground equipment
TILLING TIPS & TECHNIQUES rCONT^Power CompostingPower composting simply means tilling under and burying in the soil all manner of organic matter s
TILLING TIPS & TECHNIQUES rCONT^Terrace Gardening (continued) ^ ^• To create a terrace, start at the top of the slope and work down. Go back and
SECTION 5: MAINTENANCEA.WARNING: Before :: inspecting, cleaning or servicing themachine, shutoff engine, wait for all moving parts to come to a comple
*r?n>AWARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconn
*nn>AWARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconne
TABLE OF CONTENTSContent PageCalling Customer Support...
AWARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spar
*r?n>AWARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconn
*nn>AWARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconne
SECTION 6: MODELS 630C, 634F & 634B PARTS LIST(A) For Model 630C(B) For Model 634F (G) For Model 634BREFNO.PART NO. DESCRIPTIONREFNO.PART NO.DESC
MODELS 630C, 634F & 634В24
MODELS 630C, 634F & 634BREFNO.PART NO. DESCRIPTION11916719 Cable Assembly, Reverse Clutch{B} (C)21916755Upper Handlebar3 1917479Bail, Forward Clut
MODELS 630C, 634F & 634B(A) For Mode! 630C(B) For Mode! 634F(C) For Model 634BREFN0.PART N0. DESCRIPTION1 GW-9517Snap Ring2 GW-1714 Bearing, Tape
MODELS 630C, 634F & 634B(A) For Model 630C(B) For Model 634F(C) For Model 634BREFNO.PART NO. DESCRIPTION1 6W-9512Retainer, Snap Ring, "E” Ty
MODELS 630C, 634F & 634B13Inciuded with transmission when purchased as an assembly only. Remove and discard when installing the transmission o
MODELS бЗОС, 634F & 634ВHold Tines With Blunt End Toward YouLEFT-HAND TINERIGHT-HAND TINENOTE: Identify Left and Right sides of tiller by standing
SECTION 1: SAFETYThis machine meets voluntary safety standard B71.8^1996, which is sponsored by the Outdoor Power Equipment Institute, Inc., and is p
MODELS 630C, 634F & 634В30
MODELS 630C, 634F & 634ВREFNO.PART NO. DESCRIPTION1 1107382 Flat Washer, 5/162 1108841Key, 3/16“ X1-1/2= (B (C)3 1916531 Pulley, Engine Drive (B)
TROY-BILT TILLER LIFETIME LIMITED WARRANTYWHAT PRODUCT IS COVEREDAll Troy-Bilt branded rear tine walk-behind tillers with gear drive transmissions.Thi
4. Exercise caution to avoid slipping orlali-ing.5. If the unit should start to vibrate abnormally, stop the engine, disconnect the spark plug wire a
DecalsFor your safety and the safety of others, various safety and operational decals are located on your unit (see Figure 1-2)." (;Keep the dec
SECTION 2: ASSEMBLYA.WARNING: To prevent personal injury or property damage, do not start the engine until ail assembly steps are complete and you hav
Fig. 2.2: Attach handlebar.Fig. 2-3: Wheel In FREEWHEEL positionSTEP4: INSTALL FORWARD CLUTCH CABLE1. Attach the forward clutch cable bracket (P, Fig.
4. Thread the #10-24 hex nut (Z, Fig. 2-5) haifway onto the screw (V).5. Thread the screw (V) into the cable ad- juster{X). :6. Hook the cable sprin
bibKij: uHbuKLbVbLubThe transmission was filled with gear oil at the factory. However, you should check the gear oil level at this time to make certai
Commentaires sur ces manuels